Sure, the skull is biodegradable. But didn’t you know that large-scale human farming is responsible for the vast majority of CO2 emissions?!
Sure, the skull is biodegradable. But didn’t you know that large-scale human farming is responsible for the vast majority of CO2 emissions?!
Thanks for breaking it down for me! I think I’ll stick with the B650 motherboard for now.
Right, I guess I assumed CPU naming makes sense, so surely the lower number CPU must be worse in every way, right?😜
Looks like going with the 7700X is a no-brainer for me then.
As for your upgrade recommendations: Can you explain the benefits of a higher-end mainboard? I would think the mainboard shouldn’t make a huge difference, as long as it’s from a reputable manufacturer and compatible with all the other parts.
Thanks for your help!
Right, I might just see what cooler I can get second-hand. Thanks for your input!
This seems to be a bug in the slicer. I’m seeing the same issue in OrcaSlicer if the skirt height is set to more than one layer (even if the skirt is disabled). This makes sense if a skirt is used (can’t print a continuous spiral if you have to switch between printing the object and the skirt), but not if it’s disabled.
What slicer are you using? If it’s a PrusaSlicer fork, this is likely the same bug.
It looks to me like a JST SH connector: https://www.sparkfun.com/products/retired/10357
Measure the distance between the two pins - if it is 1 mm, this is most likely the connector you’re looking for.
From a cursory read of the datasheet, using the “dead time control” pin seems to be the way to go. Basically, this pin is used to set the voltage, while the error amplifier inputs (that’s the closest function to “over current protection” this chip has) are used to adjust the output according to the load. For your application, you probably don’t need to use them at all.
My instinct would be to disable the error amplifiers by connecting pins 1,2,15 and 16 to GND. You can then connect the wiper pin of the potentiometer to the deadtime control input, with the other pins of the potentiometer connected to GND and 3.3 V.
I haven’t worked with this chip before, so take this with a grain of salt. You should probably use a simulation tool to check the circuit before you start destroying chips.
You can bring the resting position of the brake lever closer to the handlebar by turning this screw clockwise. The brake lever looks a bit short for my taste, it’s probably not designed for use with that type of shifter. But with a bit of adjustment it should still be usable.
Do you expect every meme to be meticulously handcrafted? It’s a stupid joke, not a work of art.
Close, but the word ends in -le, not -ie. The -le suffix is used as a diminutive form in some German dialects.
A small pair of vernier calipers. I don’t use them a lot, but sometimes they come in very handy.
If that freehub is constructed like the ones I’ve taken apart before, you’re out of luck. Like you suspected, the teeth lock the rotation of the freehub to the hub, unless the screw in the back is taken out first.
You can try hammering in a (slightly larger) torx key or using an easy-out (probably won’t work if it’s very tight).
As a last resort, you could try to drill out the screw (only so far that the freehub comes off, you don’t want to drill into the hub). Then you should hopefully be left with enough left of screw to grab with a pipe wrench.
My router is called Jupiter, everything connected to it is named after a moon. Callisto, Ganymede, Thelxinoe, Kallichore are what I’m currently using.
IIRC, this is actually done at some point in the books.
You can host a Firefox sync server yourself. You could run that on something like a Raspberry Pi in your local network. If you need remote access, use something like cloudflare tunnels (although I guess that’s something else to be paranoid about).
Windows is clearly superior. If you’ve had enough of the settings app, you can just switch to the control center!
Reminds me of this: Falsehoods Programmers Believe About Names
What did you expect? We’re talking about one guy who might have lived over 2000 years ago. You’re not going to find his birth certificate and social security number.
The best anyone can do is assign a probability to his existence. And reading the article you yourself linked to, that probability seems to be pretty high.
It is more efficient to have a ship moving with cargo than without, but that doesn’t mean there aren’t additional emissions. The ratio of profit to effort is just higher because there is some profit as opposed to none. You wouldn’t load a ship up with useless mass you can’t sell just so you’re shipping something.
Your argument is like always running the heater in your car because that way the engine heat is at least used for something. Yes, technically the efficiency goes up because more of the energy in the fuel is harnessed. But that doesn’t mean the fuel usage or emissions are any lower, and in the summer the heater doesn’t do you any good either.
You can use a boost converter to boost the 5V of an USB port to the 19V your notebook needs.
Assuming 5A output from a powerbank (which is probably about the max you will get without USB PD), you could theoretically get 0.55A at 19V. With the unavoidable inefficiencies, you will get less.
So, maybe enough to very slowly charge your notebook while it’s off. But when it’s turned on, the battery charge will still drop.