- 0 Posts
- 20 Comments
8·2 months agoFrankly, once you get more than just a few cameras, being able to edit a config file is so much better than having to click through settings for literally hours like with Shinobi or Motioneye.
I’ve personally been quite pleased with the combination of Frigate and some Amcrest POE cameras. Just make sure the cameras you are getting support RTSP though and you should be able to use them with Frigate.
Also make sure you block the cameras from reaching the public internet using your firewall, and only make them reachable from your Frigate host. Personally I use a VLAN with no internet access and enforce tagging at the switch level (i.e. don’t trust the cameras to maintain their own VLAN) settings.
Looks a lot like a carburetor float needle to me. It allows the flow of gasoline into the float bowl, which sets the amount of fuel fed into the engine.
It’s common for float needles (and carb parts in general) to be made of brass, and the wire clip being made out of steel is also consistent with a float needle. The plastic tip is probably used for a better seal when the float is up, closing the needle port.
2·6 months agoI wouldn’t bother with vacuum bags If I were you. I think it’s fine if you’re using a drying box after the filament has been sitting out a while. Doesn’t hurt to try and find out at least…
Personally, I just use a big plastic storage bin with a bunch of silica desiccant in it. I just busted out some polycarbonate (notoriously hydrophyllic) recently that had been sitting in there for 4+ months and printed straight away; no stringing or anything.
Never leave anything on the toilet tank lid - you may someday have to rush to get it off so that you can push the flapper down and stop any more water from going into the bowl.
I use the washable gluesticks for my polycarbonate prints. I just put PC prints under warm water for a few minutes and they pop right off. Gluesticks generally reduce bed adhesion though IME, so it’s a fine line to walk; I never use gluesticks with PETG for example because then the parts don’t stick to the bed enough.
This one is from 1988 (see the right edge, top). Larson already retired from being a cartoonist in 1995.
4·10 months agoPresumably via Xwayland, but I haven’t tried it.
I’ve had a good experience with Onboard.
Tt-rss has been reliable for me, and the frontend is decent. Not to mention you can just republish feeds for a different frontend to use.
18 grams of espresso beans produces 45 grams of espresso liquid when running the machine for 30 seconds.
4·1 year agoYup, that’s true, and I am always open to and looking for new opportunities, but that also requires them to be interested in hiring me - not a trivial feat, especially in the current job market.
I’d also wager that the number of job positions writing OSS for organizations like that is much lower than proprietary job positions.
But you know what, I’ll go shop around a little in my free time the next week or two. I’d love for (more of) my work to be publicly accessible and not locked up in a proprietary codebase.
Yup, as a software dev, I would love to be able to devote all my time to writing open source, but I gotta make money to live as well. Switching to working on OSS would be a huge leap of faith that there is someone out there willing pay/donate for my work. As it is, I think it will be my way of giving back once I have saved up enough money from my proprietary work, and hopefully I will be able to switch over sooner rather than later.
Maybe I’ll go take a look at what the process is for getting grants from the government or non-profit orgs like Apache foundation…
I was always taught that you’re supposed to slap the load twice while saying “That’s not going anywhere” after all the straps are tight, but it might just be a regional thing.
Yeah, you just need to get the third dimension involved to make it work. Pythagoras would be fine with it.
That’s the reason you pass on node? Compared to all the others?
And that choice is Robin Williams. The man was a gem 🥲